First of all, What is Progressive Overload?
Progressive Overload is simply doing more over time. It's the most important law in strength training. There are many ways to achieve it, increasing load on the bar, increasing the amount of sets you are doing, increasing the number of repetitions, reducing the time of your session or increasing range of movement.
Now this isn't the easiest article for me to write, due to the varying abilities and fitness levels of people who may read this article, so i'll give the best advice I can given the circumstances.
First and foremost, before I get into the nitty gritty. You need to make sure your technique is perfect before you start increasing load or volume. Not everyone can start squatting with load straight away, you may have flexibility or strength restrictions that you need to address first. For example one of my clients had to start squatting off of a 24" box for her to be able to hold perfect form. If you are a beginner start with the simplest form of a movement you can and work upward.
If you are experienced you also need to make sure your form is perfect. Far too many people compromise form for load or volume. Ive seen far too many lifts like the one below, where people let the form go, just so they can tell their mates that they can lift 200kg ( if you are lifting like that, you can not deadlift 200kg).
As I mentioned earlier, there are many ways of progressing, so I am going to take you through just a couple.
Range Of Motion
An important and effective method of progressive overload is ROM (range of motion).
This is the most important method of progression and far too often overlooked. Everyday you will see someone in the gym benching with the bar 6 inches off of their chest or squatting about 3-4 inches with a crazy amount of load on their back.
If this is you, change it NOW!. Don't look at dropping the load as a step back, it isn't! When you increase the range of motion it is progression. Every extra inch of range you get, is your body getting stronger.
Training heavy through partial range can also be quite dangerous. If you only work through that particular range, then you will only be building strength and stability through that range. For example if you end up squatting a little lower through a range in which you haven't built enough stability, then you are putting your back and hips under immense stress and this could lead to injury.
You will always be better off taking a bit of load off and becoming stronger and more stable through your full range.
Sometimes, a lack flexibility, strength, stability or a combination of the three, won't allow you to work in full range of motion, even with just your bodyweight. Im going to use my client from earlier as an example for how to progress in this situation.
She started out squatting on a 24" box, as this was the only range that she was strong enough to squat in and maintain a strong technique. Once she was able to work through her given amount of reps (we started with 8) whilst maintaining correct technique, I would drop the box height by a few inches and then repeat the process.
After a few weeks of gradually reducing the height of the box, she had built enough strength to be able to squat full range without the need of a box.
Another common exercise people have problems with is the deadlift. So again start by gaining confidence with a light load and lift the bar off of blocks. As you get stronger gradually lower the height of the blocks, all the while making sure your form is correct. Eventually you will be deadlifting well from the floor and that is when you can think start looking at adding extra load.
Rep Range Method
This is a very effective method of progressive overload, and it is also simple enough for me to explain in an article.
The idea is to basically set yourself a rep range to work in for a given exercise.
Just as an example lets say you wanted to improve your squat strength and also build a bit of muscle. You would work in the 4-6 rep range for that movement. Lets say on your first set, you managed to squat 60kg with perfect form for 6 reps, then the following set you would up the load to 65kg.
If you were then only able to manage 4 or 5 reps for the remaining sets, you would stick with that weight the following squat session. The aim of the next session would be to gain improvement through gaining an extra rep or two.
It is a lot easier to add one rep to your next session than it is to add load to the bar extra week. Being able to load the bar every week is the dream, oh how I miss those beginners gains :(
If you got your 6 reps at 60kg and then were only able to manage 3 at 65kg. Then you should drop back to 60kg and work until you are getting multiple sets of 6 reps at that weight. Once you have done this you should have enough strength to be able to up the weight.
This method will ensure that you will be increasing volume through most weeks of your programme and that is the key to getting results.
Remember in doing this, NEVER compromise form. You only increase the weight if you are able to get to the top end of the rep range without losing form.
Very brief I know, but hopefully you get the picture!
if you need any more advice, or would like to enquire about training with me. get in touch!
Im based in Brentwood, Essex on weekends and in City of London during the week/
email - chris.rowlatt@yahoo.com
twitter - @chrisrowlatt
facebook - https://www.facebook.com/pages/Chris-Rowlatt-Personal-Training/234081446787193

















